Results 1 to 5 of 5
  1. #1

    Need Help With Wheels...

    Hey Guys,
    Well, first off, I'd like to say that I'm totally clueless to metal working
    besides simple grinding and such..So don't beat me if I use any wrong
    terminology.

    I have a set of 14" wheels and tires that I just bought for my car (used).
    The lug pattern fits exact but the hub holes in the wheels are too small.
    They're 2" holes and need to be 2 1/4 to fit over my hubs. I tried grinding
    them to no avail.

    Key points -
    The wheels are 14" and aluminum

    The bigger hole only needs to be a little deeper than a 1/4 inch.

    I'm trying to keep from removing the tires because I'm dirt poor and can't
    afford it. I bought the wheels and tires for dirt cheap.

    Does anyone have any ideas on how this can be done? And how much
    it will cost me? I live in the Detroit area and really don't even know who
    to call about this kind of thing.

    Any help would be appreciated.

    Thanks in advance.

  2. #2
    Registered User tigmushy's Avatar
    Join Date
    Dec 2007
    Location
    forest lake minn
    Posts
    7

    Re: Need Help With Wheels...

    Yikes. for your car??? If it was for atv trailer or something used off road I would say to use a alum grinding wheel or carbide die grinder for nonfarrous or piggyback holesaws.
    For a car... get the right rims Its your life and others.
    good luck Daye

  3. #3
    Administrator Cebby's Avatar
    Join Date
    Aug 2005
    Location
    Pittsburgh, PA
    Posts
    1,300

    Re: Need Help With Wheels...

    To do it right, you'd want to take the tires off and have it machined in a mill. Are the OEM wheels on your car lug or hub centric? All in all, probably more cost in modifying them than they are worth.
    My vehicle sites: 1993 Toyota 4Runner & 2000 Jeep Grand Cherokee

    **NEW** - UZswap.com - a site dedictated to sharing tech about swapping Toyota V8's into 4Runners and Trucks

  4. #4
    Registered User VegasBruce's Avatar
    Join Date
    Sep 2006
    Location
    Henderson, NV./ Huntsville TX.
    Posts
    127

    Re: Need Help With Wheels...

    Pull the tires off and have them milled out, that is the right way. That is what the tire shops used to do in the 70's when a lot of the aluminum rims where new and came with 1 size center hole.
    Bruce

    A craftsman is someone who does a better job than anyone thinks is necessary.

    www.4x4mecca.com
    http://www.tbucketeers.com/

  5. #5
    Registered User Glenn's Avatar
    Join Date
    Jul 2006
    Location
    Central Florida
    Posts
    342

    Re: Need Help With Wheels...

    Do it right to be safe.

    Go get a cheap cylinder hone and use a drill to bore it open if you want to do it cheap and not be safe. The cylinder hone (NOT A BRUSH HONE) will open the hole fairly equally. You will want to make a reference mark around the hole and hone until you are close. Then take it a little at a time until you get there. Stop occasionally and check it with a caliper to see if it is correct.

    I am talking about this kind of hone (which can be obtained at most auto part stores)


    NOT THIS KIND!


    Disclaimer: Your mileage may vary. You accept all risks involved if you choose to do this job. Neither I, nor anyone on this website, in any way, may be held liable for anything that might go wrong. I have provided this information for informative purposes only and in no way endorse the use of this information in an actual hands on environment. USE AT YOUR OWN RISK!
    Glenn H. Shelton III
    My Garage Pics

Similar Threads

  1. Smith & Arrow cutting wheels
    By 84ZMike in forum Metal Grinding/Dressing/Finishing
    Replies: 1
    Last Post: 11-16-2008, 09:48 AM
  2. THE place to go for Roloc Discs, Flapper Wheels
    By MXtras in forum Miscellaneous Fabrication
    Replies: 13
    Last Post: 05-07-2008, 05:52 PM
  3. Model car wheels I am making.
    By astroracer in forum Metal Sawing, Machining, and Forming
    Replies: 7
    Last Post: 02-16-2007, 01:49 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •